Tag Archives: strainer

Better price, Top Quality, expert Service support. Live demo of multiple products. Owned and operated company. Maintain a crystal clear and sparkling pool or spa that everybody loves with the new SPPE series self-priming 1850W electric swimming pool pump. Premium Material – Reinforced thermoplastic can resist the damage of chemicals in the swimming pool. Anodized Motor Body – Anti-corrosion anodized motor body prolongs its working life. Overloaded Protection – Prevents from overcurrent running that would cause overheating of the equipment. Huge Prefilter – The Strainer basket with internal ribs can filter out the debris and leaves that greatly reduce the frequency of cleaning and maintenance. Convenient Drain Device – Equipped with a drain plug on the bottom which is easy for drainage and avoids water accumulation during winter. Just revolve the stopper and pull it out. Locate the pump as close as possible to the pool. The pump suction line should not be smaller than the pressure line. All piping must be airtight. The threads on the pump must be sealed with Teflon Tape or Silicon, when the pump unions are screwed on. The weight of the piping should be supported independently and not carried by the pump. Fill the pump tank with water before starting. High suction lifts, or long suction lines, require additional time and reduce the performance of the pump. The water being pumped cools and lubricates the seal. After the pump tank has been filled with water, and the motot started, allow a few moments for the pump to start delivering water. The installation must be according to the normal power indicated on the label. The amperage must not at any time exceed the value indicated on the label. It is recommended that you consult a state-registered electrician. Place the pump in a dry area with good ventilation. The ambient temperature must not exceed 40? The pumps are only suitable for counter-clockwise rotation when viewing from the pump end. Three phase motors can rotate in either direction. Interchanging any of the cables on a three-phase motor will reverse the rotation. Momentarily start, or bump the motor without water in the tank, to check the rotation of the pump shaft. Before disconnecting electrical connections, shut off electricity at its source. Newer work on pump without making certain the power is OFF. This appliance is not intended for use by persons, including children with reduced physical, sensory or mental capabilities or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a responsible for their safety. Children should be supervised to ensure that they do not play with the appliance. Voltage : 110V / 60Hz. Head : Max 19m / 62.34ft. Diameter of white connector : 48.5mm/54.5mm. Pipe Compatibility : Fit 1.5 inch plumbing internally. Weight : 10.2 kg / 22.5 lbs. Powerful Self-Priming IP55 2.5HP Electric Motor, low noise with quiet operation and no leak. Suitable for pools up to 100,000 litres. Advanced S-Tek Flow System For Increased Efficiency With Continuous Flow Rate Of 560L/min. Full Size Removable Strainer Basket. 100% Salt and Chlorine compatible. Full Commercial Duty – Designed to run 24/7. Works with In ground and Above Ground. Built-In Thermal Overload Protection. Ideal for Residential/Commercial Swimming Pools & Spa’s. SPPE250 Swimming Pool Pump X 1. White Connector X 2. User’s Manual X 1. All items are dispatched from our warehouse in CA, NJ, AL. We seeks to sell the greatest value products on the market. These items should be of an acceptable quality, fit for purpose, and matching their description. We have a highly experienced engineering and technical team who specialise in researching and developing all our products. We benchmark our products against high standards and that’s why our customers keep coming back. We never want our customers to wait for parts, we have plenty of parts available for every product. Please contact our customer service team immediately if. You changed your mind and wish to request a return. Please do not return or post items before obtaining instructions from us. This also applies to orders cancelled while in transit. Please make sure that item has NO man-made sabotage. Used items will not be accepted for return. We will require a picture of the damaged part for verification.

For more information on our products. Please send message to us. InGround Swimming Pool Pump Motor w/ Strainer Generic Hayward Replacemen 1.5HP. What Customers Have To About Us. ” Delivered as promised and item is as described “. Just what i was looking for. Had a problem-was able to successfully resolve it. This swimming pool pump is made with heavy-duty, corrosion-proof construction. The stainless steel motor shaft is constructed with a reinforced thermoplastic body for longer life and durability. Advanced engineering provides high efficiency and minimal noise. This wonderful swimming pool pump will surely keep your above ground and inground pools clean. Please connect only to a grounding type receptacle protected by a ground-fault circuit-interrupter (GFCI). To reduce the risk of electric shock, install at least 10 feet from the inside walls of a pool. Do not use an extension cord. This pump is for use with permanently installed pools only-Do not use with storable pools. POWERFUL PUMP — This pool pump is quiped With IP55 1100W electric motor, high efficiency Impeller maximize flow and reduce noise, offers dependable performance, energy efficiency and quiet operation. Copper wire motor provides not only a more efficient, stable and safe operation, but also has a longer service life compared to ordinary motors. The powerful flow can achieve 6500 GPH and the maximum head lift can reach 51 ft. STURDY CONSTRUCTION — This 1.5HP Pool Pump is featured with commercial-grade reinforced thermoplastic shell and stainless steel motor housing, provides you with high-performance suction power and optimal flow. Suitable for swimming pools, hot tubs, thermal springs, spas and irrigation system. Ideal for all-weather performance and quiet operation. The 100% drip proof, heat-resistant seal offers a long motor life. WIDE APPLICATIONS — The Single-Speed 1.5 HP Pool Pump is designed specifically for ABOVE GROUND and INGROUND pools. Designed a voltage-switch-button at the bottom of the motor, Compatible with 115V and 230V Dual Voltage, meet all your needs. HUMANIZED DESIGN — Equipped with a drain plug on the bottom which is easy for drainage and avoids water accumulation during winter, provides easy maintenance of pump. Extra-large filter basket with clear cover keeps pool maintenance to a minimum. Transparent cover helps to judge if the basket needs clean or not;The pool pump has built-in thermal overload protection and provides pressure protection, can withstand liquid temperature up to 140? . SECURITY ASSURANCE — This Swimming Pool Pump has a UL Certification to ensure recognized standards for safety. Easy start up fill pump with water upon first use to prevent motor from overheating, make sure the safety of application. What’s more, an earthing terminal is set to connect the line on the ground for an extra layer of security. Any problems about this product will be given best solution in 24 hours. Our machine does not allow you to disassemble the cable. This product is the highest standard of UL certification. If you wire it yourself, the machine will not work properly. Thank you for your cooperation. 1, The Pump Pressure is low; The Pump loses Pressure after being energized; Pump is running, But no water coming out. Causes: The pump head is not filled with water, causing the pump to run without water. During the installation process of the pump, the inlet and outlet pipes are not tightly sealed, and the air leaks inside the pump head. During the operation, the air inside the pump head is pulled in, resulting in insufficient internal pressure, weak pump pressure, no pressure on the pump, no water. When pumping water, the pump head is filled with water; the pump head transparent cover is tightened; the water pumpinlet and outlet joints are installed, and the raw material belts are tightened when the pipes are installed to prevent air leakage at the joints of the pipes. Before pumping, the pump head should be filled with water. Inlet and outlet joints wrapped around the raw material tape, beware of leaks. Tightening when installing the inlet and outlet, beware of leaks. The pump head transparent cover is tightened to prevent air leakage and water seepage 2, Pump motor trip Causes. 1, The water pump motor enters water or pump operating environment is excessively humid, and causing the motor to short-circuit and burn. 2, The pump prevents the inlet from entering the water and burns the motor. 3, There is Water in The Pump. Causes: Our company carries out a full inspection (pumping) of the water pump, and it might result in some package still leave some water in it, It is normal. 4, The Pump stop working suddenly. Causes: Our company’s products are equipped with temperature protection device, when the motor temperature is too high, the temperature protection device will start, It will stop pump working, if the motor is shut down in the normal operation process, generally there is foreign matter inhalation in the pump, resulting in the impeller stuck, motor temperature rise, pump stop working. Solution: Clean up the waste inside the filter screen of the water pump regularly to prevent the waste foreign matter from flowing into the water pump to jam the impeller. Disassemble the pump body, clean up the foreign matter on the back of the pump body to ensure that there is no foreign matter blocking the impeller, and re-assembly can be reused. The foreign matter of the pump impeller and the diffuser is matched with the foreign matter, causing the impeller to be stuck and cleaning the foreign matter. 104 Degree Fahrenheit (40 Degree Celsius). 1.5HP Dual voltage Swimming Pool Pump. This Swimming Pool Pump has a ETL/CSA Certification to ensure recognized Standards for Safety. High performance, energy saving motor with stainless steel shaft could stand wear and tear. Thermally protected motor for greater protection and longevity. Extra-large debris basket keeps pool maintenance to a minimum, letting you enjoy your pool more, while the clear cover lets you see exactly when the basket needs cleaning. Easy start up fill pump with water upon first use to prevent motor from overheating. Transparent cover helps to judge if the basket needs clean or not. Massive strainer basket holds extra capacity. Suggested Installation: 24″-26″ sand filter and above-ground pools. 304 grade stainless steel motor shaft, Powerful Pool Pump heavy-duty, high-performance motor with air-flow ventilation for quieter, cooler operation. Strainer basket to minimize how often you have to empty it. See-through strainer cover for a fast and easy check of the strainer. Easy-thread strainer housing ring makes cover removal extremely easy. Dependability with carborundum and graphite mechanical seals and components molded of corrosion-proof, reinforced thermoplastic. Convenient drain plug makes winter maintenance easy. High Efficiency Impeller maximize flow and reduce noise while the energy efficient motor with commercial-grade frame; Internal Inlet Fitting: 1.5″ NPT (fit for 1.5″ male threaded adapter). All items are dispatched from our warehouse in HACIENDA HEIGHTS, CA. Some products may be dispatched in more than one carton. International Buyers – Please Note. If you have a problem with the product. We will require a picture of the damaged part for verification. We offer detailed product descriptions and images to give you a real advantage in finding the products you’re looking for. 25 years Industry Experience.